Energy Saving Industrial Drying Equipment For Printing /
Pharmaceutical Sludge
Equipment Introduction :
Sludge refers to the sediment produced by dealing with waste water
through the physical, chemical,
biological methods, According to their sources, which can be
divided into electroplating sludge, printing
and dyeing sludge, tanning sludge, paper sludge, pharmaceutical
sludge, sewage sludge, living sewage
sludge and petrochemical sludge, etc. Because of its features of
poor mobility, high viscosity, easy to
agglomerate, and the water is not easy to evaporate and so on, it’s
very hard to dry, and the high drying
technology is required (the drying technology of this drying system
is also adopted to dry the coal
slime, gypsum and other similar wet sticky materials).
With the continuous enhance of people's awareness of environmental
protection, and sludge drying
technology is also in the rapid development, the constant
innovation and improvement also happens in
the aspects of energy saving, safety, reliability, sustainability.
Our company energy saving sludge
industrial drying equipment is going to reduce the water content of
dewatered sludge from 80 + 10% to
20 + 10%. The advantages of our system are as follows:
1. The weight of the dried sludge can be reduced to 1/4 weight of
wet material before drying, which
greatly reduces the enterprise's environmental and economic
pressure;
2. The air inlet temperature of the dryer is 600-800℃, and it can
be used for sterilization, deodorant, etc.
at the same time of drying, and reliable guarantee will be provided
for the utilization of dried products;
3. The dried products can be used as feedstuff, fertilizer, fuel,
building materials, and raw materials for
extracting heavy metals, to realize waste utilization.
4. By adopting thermal resistant material on surface of shell, so
as to prevent heat loss. In this way, it
reduces fuel consumption, that is to say, energy saving.
The dewatered sludge will be transported to feeding head of the
dryer through the screw conveyor after
scattering, and then it will be sent into the inside of the dryer
through the unpowered spiral sealing
feeder (the patent technology of our company), and going through
several following working areas after
getting into the dryer:
1. Material leading-in area
The sludge will come into contact with the high temperature
negative pressure air after getting into this
area and plenty of water will be rapidly evaporated, and the sludge
can’t be formed into sticky stuff under
the stirring of large guide angle lifting plate.
2. Cleaning area
The material curtain will be formed while the sludge is lifted up
at this area, and it will cause the material
stick on the cylinder wall while it’s falling down, and the
cleaning device is installed at this area (Lifting
style stirring plate, X type second time stirring plate, impacting
chain, impacting plate), the sludge can
be quickly removed from the cylinder wall by the cleaning device,
and the cleaning device can also
crush the materials which are bonded together, so as to increase
the heat exchange area, increase the
time of heat exchange, avoid the generation of wind tunnel
phenomenon, improve the drying rate;
3. Inclined lifting plate area
This area is the low temperature drying area, the slime of this
area is at the low moisture and loose
state, and there is no adhesion phenomenon at this area, the
finished products reach the moisture
requirements after the heat exchange, and then enter the final
discharge area;
4. Discharging area
There aren’t stirring plates at this area of the dryer cylinder,
and the material will be rolling to the
discharging port.
The sludge gradually becomes loose after drying, and discharged
from the discharging end, and then
sent to the designated position by the conveying device, and the
fine dust drawn out along with the tail
gas is collected by the dust collector.
Hot air enters into the drying machine from the feeding end, and
the temperature is gradually reduced at
the same time of material convection heat transfer, and the water
steam taken out under the suction of
induced draft fan, and then emitted into the air after processing.
Technical Data:
| Model | Shell diameter(mm) | Shell length(mm) | Shell volume(m³) | Rotary speed(r/min) | Power(kW) |
| HG0.6×6 | 600 | 6000 | 1.7 | 1-8 | 3 |
| HG0.8×8 | 800 | 8000 | 4 | 1-8 | 4 |
| HG1×10 | 1000 | 10000 | 7.9 | 1-8 | 5.5 |
| HG1.2×6 | 1200 | 6000 | 6.8 | 1-6 | 5.5 |
| HG1.2×8 | 1200 | 8000 | 9 | 1-6 | 5.5 |
| HG1.2×10 | 1200 | 10000 | 11.3 | 1-6 | 7.5 |
| HG1.2×11.8 | 1200 | 11800 | 13.4 | 1-6 | 7.5 |
| HG1.5×8 | 1500 | 8000 | 14.1 | 1-5 | 11 |
| HG1.5×10 | 1500 | 10000 | 17.7 | 1-5 | 11 |
| HG1.5×11.8 | 1500 | 11800 | 21 | 1-5 | 15 |
| HG1.5×15 | 1500 | 15000 | 26.5 | 1-5 | 15 |
| HG1.8×10 | 1800 | 10000 | 25.5 | 1-5 | 15 |
| HG1.8×11.8 | 1800 | 11800 | 30 | 1-5 | 18.5 |
| HG1.8×15 | 1800 | 15000 | 38.2 | 1-5 | 18.5 |
| HG1.8×18 | 1800 | 18000 | 45.8 | 1-5 | 22 |
| HG2.2×11.8 | 2200 | 11800 | 44.8 | 1-4 | 22 |
| HG2.2×15 | 2200 | 15000 | 53.2 | 1-4 | 30 |
| HG2.2×18 | 2200 | 18000 | 68.4 | 1-4 | 30 |
| HG2.2×20 | 2200 | 20000 | 76 | 1-4 | 30 |
| HG2.4×15 | 2400 | 15000 | 67.9 | 1-4 | 30 |
| HG2.4×18 | 2400 | 18000 | 81.4 | 1-4 | 37 |
| HG2.4×20 | 2400 | 20000 | 90.5 | 1-4 | 37 |
| HG2.4×24 | 2400 | 24000 | 108.6 | 1-4 | 45 |
| HG2.8×18 | 2800 | 18000 | 110.8 | 1-3 | 45 |
| HG2.8×20 | 2800 | 20000 | 123.2 | 1-3 | 55 |
| HG2.8×24 | 2800 | 24000 | 147.8 | 1-3 | 55 |
| HG2.8×28 | 2800 | 28000 | 172.4 | 1-3 | 75 |
| HG3×20 | 3000 | 20000 | 141.4 | 1-3 | 55 |
| HG3×24 | 3000 | 24000 | 169.7 | 1-3 | 75 |
| HG3×28 | 3000 | 28000 | 198 | 1-3 | 90 |
| HG3.2×24 | 3200 | 24000 | 193 | 1-3 | 90 |
| HG3.2×28 | 3200 | 28000 | 225.2 | 1-3 | 90 |
Product Picture Show :
